|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
W55RFS27T3B DATA SHEET SUPER-REGENERATION RF RECEIVER Table of Content1. GENERAL DESCRIPTION ......................................................................................................... 2 1.1 1.2 Features............................................................................................................................. 2 W55RFS27T3B Pad Definition .......................................................................................... 3 1.2.1 1.2.2 1.2.3 1.2.4 Pad Description ................................................................................................................3 Clock Frequency Select (CKSEL) Setup ..........................................................................3 ID Setup ...........................................................................................................................4 Baseband Encoder Control Function Description .............................................................4 2. SYSTEM DESCRIPTION............................................................................................................ 5 2.1 2.2 W55RFS27T3B System Block Diagram ............................................................................ 5 W55RFS27T3B Functional Description............................................................................. 6 W55RFS27T3B Absolute Maximum Ratings..................................................................... 7 W55RFS27T3B DC Characteristics .................................................................................. 7 W55RFS27T3B Ordering Information ............................................................................... 8 W55RFS27T3B Package Information ............................................................................... 8 3.4.1 3.4.2 Bonding Pad List ..............................................................................................................8 Bonding Pad Diagram ......................................................................................................9 3. ELECTRONIC CHARACTERISTICS.......................................................................................... 7 3.1 3.2 3.3 3.4 4. DESIGN INFORMATION .......................................................................................................... 10 4.1 W55RFS27T3B Reference Design.................................................................................. 10 4.1.1 4.1.2 4.1.3 TXOUT waveform...........................................................................................................10 Application Circuit for 6 Control Functions......................................................................11 Application Circuit for 4 Control Functions......................................................................12 4.2 4.3 5. uC-Mode Control Signal .................................................................................................. 14 W55RFS27T Family FCC Certification............................................................................ 15 REVISION HISTORY ................................................................................................................ 16 -1- Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B 1. GENERAL DESCRIPTION The Winbond W55RFS27T3B is a fully-integrated, S-R (Super-regeneration) RF transmitter with fullfunction baseband command encoder and a Winbond-patented, channel-sharing algorithm that supports up to three players simultaneously. As such, the W55RFS27T3B is suitable for R/C vehicles, toys, or wireless data communication applications. The W55RFS27T3B provides two input modes: uC-mode, for general-purpose, micro-controller interfaces with the RF transmitter; and manual-mode, for a 3-player, 6-function, baseband command encoder and RF transmitter. In manual-mode, the W55RFS27T3B works conveniently with up to three W55RFS27R3C chips to provide a simple, multi-player remote control capability with low cost and high performance. The S-R RF transmitter operates on 27 MHz, 35 MHz, 40 MHz, or 49 MHz with a default data rate of 2.5 KBPS, and it is compliant with FCC part 15 Subpart C 15.227(15.235) and ETSI 300 220-1, making it easier for wireless end products to get FCC and ETSI compliance approval. In addition, the W55RFS27T3B accommodates a wide range of operating voltages (2.2 V to 5.5 V), supports 2- or 3-battery R/C toy applications, and generates highly-efficient transmissions. 1.1 Features * * * * * * Operating frequency: 27 MHz ~ 49 MHz Wide operating voltage: 2.2 V ~ 5.5 V Two input modes--uC-mode and manual-mode--for more flexibility (uC-mode) Transmission data rate up to 10 Kbps for 30%-70% duty cycle signals (manual-mode) Winbond-patented, channel-sharing algorithm that allows up to 3 players simultaneously on the same frequency band (manual-mode) R/C toy baseband control command encoder, supporting 4 or 6 functions: Forward, Backward, Left-turn, Right-turn, and 2 user-defined functions F1 and F2 (user-defined functions not available in 4-function mode) 15-dBm, high-efficiency transmissions (50 ) with minimum current consumption Power-down current consumption less than 1 uA Fewer external components required Compliant with FCC part 15 Subpart C 15.227(15.235) / ETSI 300 220-1 low-power and shortrange device requirements Operating temperature: 0C ~ 70C * * * * * -2- W55RFS27T3B 1.2 W55RFS27T3B Pad Definition 1.2.1 Pad Description SYMBOL PAD NO. I/O FUNCTIONAL DESCRIPTION S3 S4 CKSEL0 TEST CKSEL1 ANT GND VDD RESET X1 X2 ID1 ID0 TXOUT S1/~TXD S2/~ENB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 I I I I I O Ground Power I I O I I O I I Manual-mode input, internal pull-high Manual-mode input , internal pull-high Clock frequency select LSB (please see section 1.2.2 for setup) TEST=0 for 6-function mode, TEST=1 for 4-function mode Clock frequency select MSB (please see section 1.2.2 for setup) RF signal output. An external matching circuit is necessary for connecting with an antenna. Ground return path Power path RESET=0 resets whole chip, internal pull-high Input of internal crystal oscillator to connect to an external crystal Output of internal crystal oscillator to connect to an external crystal ID setting MSB (please see section 1.2.3 for setup) ID setting LSB (please see section 1.2.3 for setup) TXD Data output Manual-mode input or uC-mode: ~TXD, internal pull-high Manual-mode input or uC-mode: ~ENB, internal pull-high 1.2.2 Clock Frequency Select (CKSEL) Setup (CKSEL1,CKSEL0) CLOCK FREQUENCY (0,0) (0,1) (1,0) (1,1) 27.145 MHz 35.48 MHz 40.68 MHz 49.86 MHz -3- Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B 1.2.3 ID Setup (ID1,ID0) (0,0) (0,1) (1,0) (1,1) ID Player 1 Player 2 Player 3 uC- Mode 1.2.4 Baseband Encoder Control Function Description INPUT PIN NAME CONNECT TO 6-FUNCTION (TEST=0) 4-FUNCTION (TEST=1) Default (pull high) S1 GND TXOUT Default (pull high) S2 GND TXOUT S3 S4 (Note: F Forward; B F = 0, B = 0 F = 0, B = 1 F = 1, B = 0 L = 0, R = 0 L = 0, R = 1 L = 1, R = 0 F1 = 0 F1 = 1 F2 = 0 F2 = 1 F=0 F=1 B=0 B=1 L=0 L=1 R=0 R=1 Default (pull high) GND Default (pull high) GND Backward; L Left-turn; R Right-turn; F1, F2 Two User-defined function) -4- W55RFS27T3B 2. SYSTEM DESCRIPTION 2.1 W55RFS27T3B System Block Diagram IDn CKSEL X1 X2 S1 Oscillation /n (27~49 MHz) S2 Encoder S3 Control Circuit S4 POR PA ANT $TXD $ENB x VDD GND TEST RESET TXOUT -5- Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B 2.2 W55RFS27T3B Functional Description The W55RFS27T3B provides two operating modes, Manual-mode and uC-mode, for remote control product development. In Manual-mode, the W55RFS27T3B encodes one of up to six functions for one of up to three players, modulates it with the on-chip RF power amplifier, and transmits it to the receiver(s) (e.g., W55RFS27R3C). This transmission occurs in the same frequency band for all players, as this frequency band is divided using a Winbond-patented, channel-sharing algorithm. Manual-mode supports up to six functions: Forward, Backward, Left-turn, Right-turn (for general R/C-vehicle control) and two user-defined functions F1 and F2. uC-mode provides a digital interface for any external micro-controller to control the S-R RF transmitter easily and efficiently. This interface uses two W55RFS27T3B pins: TXD (S1), to send data; and ENB (S2), to tell the W55RFS27T3B to enter and exit power-down mode, as needed. The transmitter meets FCC/ETSI regulations for 27 MHz, 40 MHz and 49 MHz S-R (Superregeneration) modulation, and it is compliant with FCC part 15 Subpart C 15.227(15.235) and ETSI 300 220-1, making it easier for wireless end products to get FCC and ETSI compliance approval.. In addition, the W55RFS27T3B accommodates a wide range of operating voltages (2.2 V to 5.5 V), supports 2- or 3-battery R/C toy applications, and transmits at 15 dBm very efficiently. -6- W55RFS27T3B 3. ELECTRONIC CHARACTERISTICS 3.1 W55RFS27T3B Absolute Maximum Ratings PARAMETER RATING UNIT Supply Voltage to Ground Potential Applied Input/Output Voltage Power Dissipation (Ta = 70C) Ambient Operating Temperature Storage Temperature - 0.3 to 6.5 - 0.3 to 6.5 150 0 to 70 -40 to 85 V V mW C C Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely affect the life and reliability of the device. 3.2 W55RFS27T3B DC Characteristics (VDD-VSS = 3 V, Ta = 25C; unless otherwise specified) PARAMETER Power Supply Operating Voltage Operating Current (uC-mode) Stand-by Current Input High Voltage Input Low Voltage Input Pin Pull-High Resistance TXOUT Output High Source Current TXOUT Current Output Low Sink SYM. VDD ITX ISBY VIH VIL RPH IOH IOL CONDITIONS MIN. 2.2 TYP. 150K - MAX. 5.5 50 1 VDD 0.1*VDD - UNIT V mA A V V ohm mA mA Continuous emission, VDD=5.5V 0.8*VDD VSS Digital Input/Output Pin (S1, S2, S3, S4, ID0, ID1, MODE,CKSEL0,CKSEL1) S1~S4, RESET VOH=0.7 * VDD VOL=0.3 * VDD 6 6 Crystal Oscillator Operation Frequency Oscillator Turn-On Time Transmitter Section Modulation Duty Cycle Transmission Data Rate Transmission Power MDYT RDTT PANT 50% Duty-cycle RZ Code 30 50 2.5 15 70 10 % Kbps dBm FXTL TOSC Fundamental type Over-tone type 27 49 1.0 3.0 MHz mS mS Notes: (1). Crystal turn-on time depends on crystal type: fundamental or overtone type crystal. (2). Transmitter settling time depends on crystal type: fundamental or overtone type crystal. -7- Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B 3.3 W55RFS27T3B Ordering Information The W55RFS27T3B is available in two forms: Dice form and Wafer form PART NUMBER PACKAGE REMARKS W55RFS27T3B(H) W55RFS27T3B(W) Dice form Wafer form - 3.4 W55RFS27T3B Package Information 3.4.1 Bonding Pad List Window : (xl = -620.000, yl = -635.000),(xh = 620.000, yh = 635.000) Windows size : Width = 1240.000, length = 1270.000 ============================================================================= PAD NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PAD NAME S3 S4 CKSEL0 TEST CKSEL1 ANT * VSS VDD RESET X1 X2 ID1 ID0 TXOUT S1 S2 PIN NAME 1 2 3 4 5 6 *7 8 9 10 11 12 13 14 15 16 X -535.000 -535.000 -535.000 66.325 173.325 282.725 535.000 535.000 535.000 245.005 138.005 31.005 -75.995 -288.420 -535.000 -535.000 Y -69.260 -360.520 -484.865 -550.000 -550.000 -550.000 -218.395 20.945 284.600 550.000 550.000 550.000 550.000 550.000 329.000 37.740 ---------------------------------------------------------------------------------------------------------------------------------------- ============================================================================= (*: Bonding Sequence start from VSS(Pin7)) -8- W55RFS27T3B 3.4.2 Bonding Pad Diagram 3 2 1 1 1 1 4 5 6 W55RFS27T3 1 1 LOGO 1 9 1 *7 8 -9- Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B 4. DESIGN INFORMATION 4.1 W55RFS27T3B Reference Design 4.1.1 TXOUT waveform TEST ANT TEST=0 1 2 ... ... 16 TXOUT 1 2 16 Power down Any key pressed Key STOP TEST ANT 1 2 TEST=1 ... 16 TXOUT - 10 - W55RFS27T3B 4.1.2 Application Circuit for 6 Control Functions Set TEST = 0. 1. Use this circuit when F1 and F2 are required.(i.e., when more than 4 functions are required). 2. When a 9-V battery is used, an external power switch is required to save power 3. LEDs require extra components VSPLY SW1 TXOUT Forward SW3 TXOUT Left turn S1 R3 1K SW2 Backward 300 R5 LED LED1 S2 R4 1K SW4 Right turn 100u C0 S1 1N4148 D1 1N4148 D2 Input Protection S2 LED control circuit SW5 SW6 F1 F2 CKSEL0 U1 1 2 3 4 CKSEL1 5 6 VDD JP3 1 2 Power In BT1 BAT VDD VDD 7 8 S3 S4 CKSEL0 TEST CKSEL1 ANT VSS VDD S2 S1 TXOUT ID0 ID1 X2 X1 RESET W55RFS27T3B 16 15 14 13 12 11 10 9 R1 20K 49.86MHz Overtone Crystal S2 S1 TXOUT ID0 ID1 ID0 VDD JP6 1 2 3 ID0 ID1 C8 7p JP7 1 2 3 ID1 VDD L1 39nH ANTENNA L2 1uH Dependent on Antenna C13 47n C7 240p BT1 9V S1 PWR R5 120 VDD L7 1uH C9 D3 4.3V C18 470u + C19 47n 7p C33 47n * 27MHz,(L1,C7)= (56nH, 470pF), (L7,C33)=none * 35MHz,(L1,C7)= (47nH, 360pF), (L7,C33)=(3.3uH,47n) * 40MHz,(L1,C7)= (47nH, 300pF), (L7,C33)=(2.2uH,47n) * 49MHz,(L1,C7)= (39nH, 240pF), (L7,C33)=(1uH,47n) CKSEL1 CKSEL0 VDD Title Size A Date: W55RFS27T3B Application Circuit (49MHz) Document Number {Doc} Monday, May 03, 2004 Sheet 1 of 1 Rev {RevCode} For 49MHZ - 11 - Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B W55RFS27T3B Application Schematic BOM(6-function): Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Qty 1 2 3 1 1 2 1 1 1 1 1 2 1 2 Reference C7 C8,C9 C13,C19,C33 C18 L1 L2,L7 R1 U1 Y1 LED1 C0 D2,D1 R5 R4,R3 Part 240p 7p 47n 10u 39nH 1uH 20K W55RFS27T3B 49.86MHz LED 100u 1N4148 300 1K (Optional) (Optional) (Optional) (Optional) (Optional) ________________________________________________________________________________ 4.1.3 Application Circuit for 4 Control Functions Set TEST = 1. 1. Only 4 functions are provided. 2. The external power switch is not required when using a 9-V battery. 3. LEDs can be directly driven by TXOUT. - 12 - W55RFS27T3B D3 1N4148 SW3 SW4 Left-turn Right-Turn CKSEL0 D4 1N4148 1 2 3 4 CKSEL1 5 6 VDD VDD 7 8 U1 S3 S4 CKSEL0 TEST CKSEL1 ANT VSS VDD S2 S1 TXOUT ID0 ID1 X2 X1 RESET W55RFS27T3B 16 15 14 13 12 11 10 9 D2 1N4148 D1 1N4148 SW2 SW1 TXOUT ID0 ID1 C8 7p Backward Forward TXOUT 300 R5 LED LED1 R1 20K 49.86MHz Overtone Crystal L1 39nH ANTENNA L2 1uH Dependent on Antenna C13 47n C7 240p JP6 1 2 3 ID0 VDD ID0 ID1 JP7 1 2 3 VDD ID1 L7 1uH C9 7p C33 47n R5 120 VDD BT1 9V D3 4.3V C18 470u + C19 47n * 27MHz,(L1,C7)= (56nH, 470pF), (L7,C33)=none * 35MHz,(L1,C7)= (47nH, 360pF), (L7,C33)=(3.3uH,47n) * 40MHz,(L1,C7)= (47nH, 300pF), (L7,C33)=(2.2uH,47n) * 49MHz,(L1,C7)= (39nH, 240pF), (L7,C33)=(1uH,47n) CKSEL1 CKSEL0 VDD Title Size A Date: W55RFS27T3B Application Circuit (49MHz) Document Number {Doc} Tuesday, May 04, 2004 Sheet 1 of 1 Rev {RevCode} For 49MHZ - 13 - Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B 4.2 uC-Mode Control Signal S2(~ENB ) Oscillator Chip disabled Chip Enabled Power down 3m S1(~TXD) ANT - 14 - W55RFS27T3B 4.3 W55RFS27T Family FCC Certification - 15 - Publication Release Date:June 8, 2005 Revision A1 W55RFS27T3B 5. REVISION HISTORY VERSION DATE PAGE DESCRIPTION A0 A1 2004/7/6 2005/5/30 - Preliminary version A0 Released version A1 (Revised by Brand) and important notice Important Notice Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales. Headquarters No. 4, Creation Rd. III, Science-Based Industrial Park, Hsinchu, Taiwan TEL: 886-3-5770066 FAX: 886-3-5665577 http://www.winbond.com.tw/ Winbond Electronics Corporation America 2727 North First Street, San Jose, CA 95134, U.S.A. TEL: 1-408-9436666 FAX: 1-408-5441798 Winbond Electronics (Shanghai) Ltd. 27F, 2299 Yan An W. Rd. Shanghai, 200336 China TEL: 86-21-62365999 FAX: 86-21-62365998 Taipei Office 9F, No.480, Rueiguang Rd., Neihu Chiu, Taipei, 114, Taiwan, R.O.C. TEL: 886-2-8177-7168 FAX: 886-2-8751-3579 Winbond Electronics Corporation Japan 7F Daini-ueno BLDG, 3-7-18 Shinyokohama Kohoku-ku, Yokohama, 222-0033 TEL: 81-45-4781881 FAX: 81-45-4781800 Winbond Electronics (H.K.) Ltd. Unit 9-15, 22F, Millennium City, No. 378 Kwun Tong Rd., Kowloon, Hong Kong TEL: 852-27513100 FAX: 852-27552064 Please note that all data and specifications are subject to change without notice. All the trade marks of products and companies mentioned in this data sheet belong to their respective owners. - 16 - |
Price & Availability of W55RFS27T3B |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |